Dragino D20-LB LoRaWAN temperature sensor with 2 m stainless steel probe IP66 (868 MHz)

SKU:3JR7
Cod. produttore:D20-LB
Marca:Dragino
Categorie:
Sensoren:
Disponibilità CH:
non in magazzino0
Da magazzino esterno:
Tempo di consegnain ca. 20 giorni
Il termine vale a partire da 10 pezzi. Per quantità inferiori chiedeteci. (?)

CHF59.28 IVA escl.

più spese di spedizione

LoRaWAN temperature sensor for outdoor use with a remote stainless steel probe on 2 m of cable: DS18B20 from −55 to +125 °C, ±0.5 °C typical. IP66 enclosure, recording when the network drops, 8500 mAh cell for up to five years. For cold stores, heating systems, compost and water tanks.

! Per utilizzare questo dispositivo serve una rete LoRaWAN. Potete crearla voi stessi con un gateway LoRaWAN, usare la rete LORIOT o TTN, oppure la rete Swisscom LoRaWAN che copre tutta la Svizzera. Tutte queste reti sono acquistabili da noi.
 Aggiungi al confronto

The Dragino D20-LB is the simplest useful outdoor temperature sensor: a rugged DS18B20 in a stainless steel sleeve on two metres of cable, and the rest is radio and battery. Its range runs from −55 to +125 °C and so reaches well beyond what humidity sensors can do — deep freeze at one end, heating flow at the other. At ±0.5 °C it is not a laboratory instrument but a piece of operating equipment; in return it costs a fraction and the 8500 mAh cell carries it for years. The IP66 enclosure stays outside, the probe goes where the measurement is.

  • −55 … 125 °Cprobe range
  • ±0.5 °Ctypical, max. ±2.0 °C
  • 2 mprobe cable
  • IP66enclosure, probe IP65
  • 8500 mAhLi-SOCl₂ cell

What defines the D20-LB

  • A measuring range that covers most applications: −55 to +125 °C is not a marketing figure but the DS18B20’s range. The same device therefore measures in a deep-freeze store and on a heating return — and that is why this sensor is so often the right choice although it can do nothing but temperature.
  • The probe is stainless steel, not plastic: the sensing element sits in a stainless sleeve rated IP65. It slides into a thermowell, straps to a pipe or pushes into bulk material — and it survives the cleaning that open sensors fail.
  • Two metres of cable separate measurement from radio: the device hangs where it has coverage and stays reachable; the probe goes into the cold room, down the shaft, onto the pipe. On a compact sensor both are in the same place — here they are not.
  • A digital bus, not analogue technology: the DS18B20 delivers a digital value. There is no characteristic curve to store, no line loss to compensate and no calibration at commissioning — unlike PT100s or thermocouples.
  • An alarm flag in every message: a dedicated bit shows whether the value has left a set threshold. Thresholds are set by downlink, and so is the minimum time between two alarm messages — a sensor sitting on a limit therefore does not flood the network.
  • Recording when the network drops: if coverage fails, the device writes timestamped readings to its own memory and sends them on once the network is back. For an evidential series that is the difference between a gap and continuity.
  • Device status on its own port: model, firmware version, frequency band and battery arrive on FPort 5, separate from the readings on FPort 2. For a fleet that means the inventory can be queried without searching the measurement database.
  • A large cell, soberly reckoned: 8500 mAh of Li-SOCl₂ is three times that of a common room sensor. The manufacturer quotes up to five years — a realistic figure for a device with a single digital sensor and one transmission per interval.
  • Configuration over the air: reporting interval and thresholds are set by downlink. The device can also be configured on site over Bluetooth 5.1 and its firmware updated wirelessly — a device on a cold room stays where it is.
  • Not tied to a platform: LoRaWAN 1.0.3, Class A, OTAA. Runs on TTN, ChirpStack and the Swisscom LPN with the same device profile and the same decoder.
  • The same electronics, four probe variants: anyone needing a buriable probe takes the D20S; two measuring points on one device, the D22; three, the D23. Decoder and integration stay the same.

Where the D20-LB is used

  • Chilled and frozen stores: device outside, probe inside, cable through the door seal. The radio path does not run through the metal door — the reason cold-store monitoring otherwise has holes. And −55 °C covers deep freeze as well.
  • Heating, heat pumps, solar thermal: flow and return temperature with a pipe clamp probe, without touching the hydraulics.
  • Hot water and legionella checks: the range up to 125 °C covers every cylinder and circulation temperature; the stainless probe fits common thermowells.
  • Compost, silage, bulk material: the probe sits in the heap, the device on a post. Self-heating caught early is the difference between turning the pile and a fire.
  • Greenhouse, livestock housing, polytunnel: temperature in the crop rather than under the roof.
  • Machine and bearing monitoring: the probe at the bearing, the device outside the danger zone.
  • Water tanks and cisterns: the probe hangs in the tank, the device on the lid — the probe’s IP65 is built for that, though continuous operation under water is not specified.
  • Large rollouts: one article, one decoder, one spare — and through the D20-LS, D20-NB and D20-CB variants the same measuring technology with a different form of power or radio.
±0.5 °C is the typical tolerance, not the guaranteed one. Dragino explicitly states up to ±2.0 °C as the maximum across the whole range. For trends, threshold monitoring and running a plant that is enough; for an acceptance measurement or a calibration record it is not. Anyone who has to prove half a degree needs a PT100 — for example the LTC1 from the same series. It does not measure humidity. Where humidity is part of the question — storage, room climate, mould risk — the S31B is the right device. The cable is two metres long and fixed. It passes through the gland and cannot be extended; a measuring point further away needs a different arrangement. And the cell is not rechargeable. At the end of its life it is replaced, or the device is; anyone wanting to avoid that takes the solar version D20-LS.

That covers the purchase decision. What follows is the depth needed for mounting, integration and operation.

What ±0.5 °C means in practice

The DS18B20 has been the standard sensor for exactly this class of task for decades, and its tolerance is well documented: in the middle of the range it typically holds half a degree, at the edges of the range considerably less well. Dragino states this correctly as ±0.5 °C typical and up to ±2.0 °C maximum — a detail many suppliers leave out.

Consequence for planning: what decides is whether the application needs an absolute value or a change. A cold chain with a limit at −18 °C does not tolerate half a degree of uncertainty well — there the threshold belongs set conservatively, or the sensor checked against a reference instrument. Compost monitoring, where fifteen degrees of rise is the point, tolerates it easily.

Assessment from field practice, not a manufacturer statement: the larger error usually sits not in the sensor but in the installation. A pipe clamp probe without heat transfer compound and without insulation reads several degrees low depending on room temperature; a probe hanging against the wall of a cold room rather than in the air measures the wall. Anyone who installs it properly gets more out of this sensor than out of a more accurate sensor badly placed.

Payload and integration

The readings arrive on FPort 2 in eleven bytes of fixed order: two bytes of battery voltage in millivolts, two bytes of temperature from the connected probe as a signed value with a factor of ten, two unused bytes, one byte with the alarm flag, the operating mode and the state of input PA8, then two times two bytes for the probes this model does not have — they read 0x7FFF. D20, D22 and D23 share exactly this field layout; the decoder is the same for all three.

Device status — model (0x19), firmware, frequency band, sub-band, battery — runs separately on FPort 5, and the replayed stored values on FPort 3. The latter each carry a four-byte Unix timestamp.

For the integration that means three things. First: the decoder has to evaluate the port, otherwise status messages land in the time series as implausible readings. Second: 0x7FFF is not a reading but “no probe” — anyone not catching it gets 3276.7 °C into the database. Third, and unlike the humidity sensors from the same brand: the live message on FPort 2 carries no timestamp. The measurement time here is the time of receipt; only the replayed stored values bring their own time, and only there does the evaluation have to use it.

Data at a glance

Sensing element1 × Dallas DS18B20 in a stainless steel sleeve, IP65, 2 m cable
Temperature−55 … +125 °C · ±0.5 °C typical, up to ±2.0 °C maximum · resolution 0.1 °C
Operating temperature−40 … 85 °C (device)
RadioLoRaWAN 1.0.3, Class A, OTAA · EU868 · up to +22 dBm · sensitivity down to −139 dBm
PayloadFPort 2 readings (11 bytes) · FPort 3 stored values with timestamp · FPort 5 device status
ConfigurationLoRaWAN downlink · Bluetooth 5.1 on site · firmware update over the air
Power8500 mAh Li-SOCl₂, not rechargeable · quiescent current 5 µA at 3.3 V · manufacturer: up to 5 years
EnclosureIP66 · 200 × 120 × 55 mm · 372 g
VersionsD20-LB LoRaWAN battery · D20-LS LoRaWAN solar · D20-NB NB-IoT · D20-NS NB-IoT solar · D20-CB LTE-M and NB-IoT · D20-CS LTE-M and NB-IoT solar

What the manufacturer does not state: Dragino does not name the probe cable’s material for the D20 — on the buriable D20S it is explicitly TPE, on the D20 it is left open. A dimensioned drawing of the probe is also missing; the diameter and length of the stainless sleeve appear neither on the product page nor in the manual. Anyone wanting to fit an existing thermowell should ask for the dimensions before ordering — we will add them at the first goods receipt.

+ Mostra altro

Dokumente

Recensioni

Ancora non ci sono recensioni.

Recensisci per primo “Dragino D20-LB LoRaWAN temperature sensor with 2 m stainless steel probe IP66 (868 MHz)”

Details

Generale
Marca
Dragino
Codice produttore
D20-LB
Colore
nero
Interfaccia
LoRa 868MHz
Version des LoRa (Long Range) Low-Power-Wireless-Chipsatzes, der auf verschiedenen Frequenzen arbeitet. Typischerweise für IoT-Anwendungen mit geringem Stromverbrauch und großer Reichweite verwendet.
Connettività
Connettività
LoRaWAN
Long Range Wide Area Network, ein drahtloses Protokoll für Low-Power-Geräte in weiträumigen Netzwerken, ideal für das IoT.
Specifica LoRaWAN
1.0.3
Classe dispositivo
A
Klasse A-Geräte ermöglichen bidirektionale Kommunikation zwischen dem Gerät und dem Netzwerk. Nach jeder Uplink-Übertragung des Geräts sind zwei kurze Downlink-Empfangsfenster geöffnet. Diese Geräte haben die niedrigste Energieeffizienz und sind für Anwendungen geeignet, die keine festgelegten Empfangszeitpunkte erfordern. Beispielsweise könnte ein IoT-Sensor, der sporadisch Temperaturdaten an eine Cloud sendet, ein Klasse A-Gerät sein.
Antenna esterna
sì
Frequenze
EU868
LoRaWAN-Frequenzband für Europa (868 MHz). Verwendet in Ländern wie Deutschland, Frankreich, Großbritannien und den meisten anderen europäischen Ländern.
Alimentazione
Alimentazione
Batterie
Pile incluse
Ja
Numero di pile
1
Tipo di pila
Li-SOCL₂
Die Li-SOCl₂-Batterie ist ein hochleistungsfähiger Energiespeicher, der Lithium (Li) und Thionylchlorid (SOCl₂) verwendet. Sie zeichnet sich durch eine hohe Energiedichte, lange Lagerfähigkeit und eine breite Betriebstemperaturbereich aus, was sie ideal für IoT-Geräte macht, die eine langanhaltende, zuverlässige Energiequelle benötigen. Im Kontext von IoT definiert sie die Fähigkeit, Geräte über längere Zeiträume autark betreiben zu können, selbst in anspruchsvollen Umgebungsbedingungen.
Meccanica/design
Peso del prodotto (g)
372
Larghezza (mm)
120
Lunghezza (mm)
200
Altezza (mm)
55
Codice IP / protezione
IP66
Staubdicht. Schutz gegen starkes Strahlwasser und bei Überflutung. Ein IoT-Sicherheitskamera im Freien könnte diesen Schutz haben.
Intervallo di temperatura
-40 °C bis 85 °C
Informazioni commerciali
Paese d’origine
Cina
Altre caratteristiche
Sensori
temperatura
Autonomia
3-5 Jahre
Luogo d’impiego
interno ed esterno
Server di rete
ChirpStack
,
Swisscom LPN
,
TTN