Dragino S31B-NS NB-IoT temperature and humidity sensor IP66 for outdoor use (868 MHz) — solar

SKU:3JR4
Cod. produttore:S31B-NS-GE
Marca:Dragino
Categorie:
Sensoren:
Sensoren Thumbnail Sensoren Thumbnail
Disponibilità CH:
non in magazzino0
Da magazzino esterno:
Tempo di consegnain ca. 20 giorni
Il termine vale a partire da 10 pezzi. Per quantità inferiori chiedeteci. (?)

CHF77.55 IVA escl.

più spese di spedizione

LoRaWAN temperature and humidity sensor in one piece: the Sensirion SHT31 sits in a condensation-proof sleeve directly on the IP66 enclosure, with no cable to route. ±0.2 °C and ±2 %RH, a stated long-term drift, and an 8500 mAh cell for up to five years. For façades, halls and greenhouses, where the measuring point and the radio location are the same place.

! Per utilizzare questo dispositivo serve una rete LoRaWAN. Potete crearla voi stessi con un gateway LoRaWAN, usare la rete LORIOT o TTN, oppure la rete Swisscom LoRaWAN che copre tutta la Svizzera. Tutte queste reti sono acquistabili da noi.
 Aggiungi al confronto

The Dragino S31B-NS measures temperature and humidity where it hangs — sensor and radio are one piece. The Sensirion SHT31 sits in a condensation-proof sleeve directly on the enclosure: no cable to route, no second mounting point. The IP66 enclosure is built for outdoors, not merely tolerated there — which makes it the outdoor climate sensor you screw to a wall and forget for five years. This version transmits without a gateway over NB-IoT onto the cellular network while being solar powered — the most demanding of the energy budgets, because cellular consumes more than LoRaWAN and the cell holds only 3000 mAh.

  • ±0.2 °Caccuracy, 0 … 90 °C
  • ±2 %RHhumidity, whole range
  • IP66enclosure
  • −40 … 85 °Coperating range
  • 3000 mAhLi-ion, solar charged

What defines the S31B-NS

  • One piece instead of two mounting points: the sensor sits in a sleeve attached directly to the enclosure. No cable to route, clamp or lead through a seal — mounting is one screwed fixing and done. Across a fleet of outdoor measuring points that is the difference between twenty minutes and five per device.
  • A Sensirion SHT31, not a house brand: the sensor fitted has a public datasheet and behaviour documented over years. ±0.2 °C and ±2 %RH are not marketing but the component’s specification — and they sit a class above what simple room sensors deliver.
  • The drift is stated, not glossed over: the manufacturer gives less than 0.03 °C and less than 0.25 %RH deviation per year. That is the figure which decides, over five years, whether a measurement series stays comparable — and the one that is simply missing from most cheap sensors.
  • Condensation-proof, not merely splash-proof: the sleeve lets humidity through but not water. That is exactly where open sensors fail outdoors: after the first condensation cycle they read permanently wrong.
  • The timestamp comes from the device: every message carries a Unix time from the sensor, not just the network server’s time of receipt. If delivery is delayed the series still stays chronologically correct — the precondition for it to serve as evidence.
  • An alarm flag in every message: a dedicated bit shows whether the value has left a set threshold. The evaluation therefore does not have to check thresholds itself, and an alarm is not lost if processing falls behind.
  • Recording when the network drops: if coverage fails, the device writes the readings to its own memory and sends them on once the network is back. For an evidential series that is the difference between a gap and continuity.
  • Device status travels along: cell voltage, device model, IMEI and serial number sit in the same message as the readings. For a fleet that means the inventory can be kept from the running data stream without querying the device — and the cell voltage doubles as the early warning before a battery change.
  • No battery change planned in: the solar panel charges a rechargeable 3000 mAh Li-ion cell. With sufficient light the replacement cycle disappears — at hard-to-reach measuring points the larger item over the service life. It still supplies the cellular module’s short, high currents.
  • Configuration without a network server: reporting interval and thresholds are set on the device or sent back through your own server. There is no LoRaWAN network server managing downlinks here — that responsibility sits with your platform.
  • No gateway, no network server: the device transmits straight onto the cellular network and sends its data to your endpoint. No device profile, no join, no key management — but a SIM that wants managing.
  • Two forms of power, one article: where no battery change is wanted, the same device comes as the S31B-LS with a solar panel and a rechargeable cell. The measuring and radio sections are identical, the integration stays the same.

Where the S31B-NS is used

  • Outdoor climate on buildings: IP66 and a condensation-proof sleeve allow façade mounting; the operating range runs from −40 to 85 °C. This device’s classic application.
  • Unheated halls, barns, storage sheds: one device, one screw, no wiring — and reachable over radio even where no line runs.
  • Stores with humidity limits: paper, timber, electronics, animal feed. ±2 %RH is accurate enough to prove a limit and not merely assert it.
  • Greenhouse and polytunnel: the sensor hangs in the crop along with the device. Condensation-proof, so still able to measure after misting.
  • Building sites and temporary measuring points: mounted in minutes, removed just as fast, nothing to route.
  • Plant rooms and service risers: where the measuring point and the device location coincide, the compact form saves the second fixing.
  • Evidence towards third parties: thanks to the device’s own timestamp and the replay from memory the series stays continuous and chronological.
  • Large rollouts: one article, one decoder, one spare — and through the S31B-LS variant the solar-powered version as well, with no new integration.
No light, no solar operation — and here it counts twice. Cellular consumes more than LoRaWAN, and the cell has only 3000 mAh. A panel in shade or down a shaft will not carry that balance through winter. Where the light is missing, the battery version S31B-NB is the right choice. Without a SIM and without a server nothing works. This version (order suffix GE) comes without a SIM card. You need an NB-IoT-capable SIM — not every data card is — and an endpoint for MQTT, TCP or UDP. Cellular costs money continuously. A data charge falls due per device per year; with several devices in one place LoRaWAN with your own gateway is almost always cheaper. Measurement happens where the device hangs. That is the whole difference from the sibling device: anyone who has to separate measuring point and radio location — cold store, shaft, hall ceiling — needs the S31 with three metres of probe cable. Both cost practically the same; the choice is one of mounting, not of budget. For plain indoor air measurement it is oversized. Where no outdoor climate and no ingress rating are needed, the Dragino LHT52 delivers the same for a fraction. IP66 is jets of water, not submersion. For a façade or a mast that is enough; in flood-prone locations the device belongs higher up. And the cell is not rechargeable. At the end of its life it is replaced, or the device is; anyone wanting to avoid that takes the solar version S31B-LS.

That covers the purchase decision. What follows is the depth needed for mounting, integration and operation.

Why the mounting location becomes a measured quantity here

On a device with a remote probe, the question “where do I measure” is separate from the question “where does the transmitter hang”. On the S31B the two coincide, and so the mounting location becomes part of the measurement. That is not a fault but a property to account for in planning — and one regularly overlooked in practice.

Consequence for planning: a black plastic enclosure in direct sun becomes warmer than the air it is meant to measure; depending on irradiation and wind that is several degrees. For outdoor air temperature the device therefore belongs on the north side, under a roof overhang or inside a radiation shield. The same applies in reverse to heat sources indoors: a device above a radiator or beside a switch cabinet measures the cabinet as well.

Assessment from field practice, not a manufacturer statement: the S31B shares this limitation with every compact sensor, and it is the real reason the cabled version exists at all. Anyone needing absolute outdoor air temperatures — for evidence, not for a trend — should plan for a radiation shield; anyone following trends and threshold breaches in a sheltered mounting position does not need one. Dragino makes no statement about sensitivity to radiation; on a device that hangs in arbitrary places that is hard to quantify anyway.

Payload and integration

Without LoRaWAN the whole apparatus of ports, device profiles and decoders falls away: there is no FPort, no network server and no payload function for anyone to maintain. The device opens a connection to the cellular network and delivers the same values — cell voltage, measured quantities, alarm flag, device identity — straight to your endpoint.

Consequence for the integration: what was the decoder in the network server under LoRaWAN is here the receiver on your side. That is less infrastructure but the same work — the raw format has to be interpreted once. The exact field order is in the manufacturer’s cellular manual, linked under “Documents”; it differs from the LoRaWAN version and belongs held against a real message once at commissioning.

One point regularly overlooked on cellular devices: the device identity comes from the IMEI and serial number, not from a DevEUI. Anyone running a fleet of LoRaWAN and cellular devices together needs a key field that can take both.

No gateway — what that costs and what it saves

NB-IoT uses the cellular network that is there anyway. So there is no gateway infrastructure to build, no coverage to plan and no network server to run. In return every device needs a SIM card and a server that accepts the data — the costs do not disappear, they move from the initial investment into running expenses.

The arithmetic that comes first: a single sensor somewhere remote is a clear case for cellular — a gateway for one device never pays. Thirty sensors on one site are an equally clear case for LoRaWAN. The boundary lies, depending on tariffs, somewhere between five and ten devices per site, and it shifts with the question of whether anyone is there to look after a gateway.

Assessment from field practice, not a manufacturer statement: what is regularly underestimated is not the radio technology but the SIM. Many standard data cards are not enabled for NB-IoT at all, and that only shows when the device fails to get onto the network at the site. On top comes administration: a hundred LoRaWAN devices hang on one network server, a hundred NB-IoT devices on a hundred SIM contracts with terms and invoices. That is not a technical but an organisational argument — and on larger fleets it decides more often than range does.

Connecting to your own server

The device speaks MQTT, MQTT over TLS, TCP and UDP. MQTT with TLS is the right choice for most applications: widespread, economical and encrypted. UDP is more economical still and therefore kinder to the battery, but offers no delivery guarantee — usable where individual lost messages are tolerable.

Server, port, credentials and topic are set on the device. There is no network server decoding the payload; the device sends straight to your endpoint. Decoder maintenance falls away, and responsibility for reachability and certificates rests with you.

Solar and cellular — the tightest energy budget

Solar and cellular are each manageable on their own; together they are the most demanding combination. A cellular module draws short, high currents when establishing a connection and, over the day, needs considerably more than a LoRaWAN transmitter, and the solar cell has only 3000 mAh, a good third of the lithium primary cell’s capacity. What works effortlessly in summer can tip over in December.

Consequence for planning: the reporting interval is not a comfort parameter here but the decisive lever — and radio quality at the site shifts the balance again, because a device at the edge of coverage transmits with more power and stays awake longer. Anyone combining solar and cellular plans the interval around winter.

Assessment from field practice, not a manufacturer statement: for this version Dragino gives neither a battery life nor a minimum irradiation — consistent, with three independent variables. What is usable instead is the cell voltage that comes with every message: anyone watching it through the first winter knows afterwards whether the site carries.

Data at a glance

SensorSensirion SHT31 in a watertight, condensation-proof sleeve, directly on the enclosure
Temperaturesensor −40 … +80 °C · ±0.2 °C in the range 0 … 90 °C · resolution 0.1 °C · long-term drift < 0.03 °C/yr
Humidity0 … 99.9 %RH · ±2 %RH across the whole range · resolution 0.01 %RH · long-term drift < 0.25 %RH/yr
Operating temperature−40 … 85 °C
RadioNB-IoT via Quectel BC660K-GL · B1/B2/B3/B4/B5/B8/B12/B13/B17/B18/B19/B20/B25/B28/B66/B70/B85 in H-FDD
ProtocolsMQTT · MQTT over TLS · TCP · UDP
SIMGE version: without SIM · nano-SIM slot · 1T version: 1NCE SIM, 500 MB over 10 years
Payloadraw format straight to your own endpoint · no FPort, no network-server decoder · field order in the manufacturer’s cellular manual
Configurationon the device or through your own server’s return channel · Bluetooth 5.1 on site · firmware update over the air
Powersolar panel with rechargeable 3000 mAh Li-ion cell · no battery-life figure from the manufacturer
EnclosureIP66 · 200 × 120 × 55 mm
VersionsS31B-LB LoRaWAN battery · S31B-LS LoRaWAN solar · S31B-NB NB-IoT · S31B-NS NB-IoT solar · S31B-CB LTE-M and NB-IoT · S31B-CS LTE-M and NB-IoT solar

On the measuring range: the manufacturer gives −40 to +80 °C for the sensor and an operating range of −40 to 85 °C for the device. The accuracy figure of ±0.2 °C refers to 0 to 90 °C and so reaches beyond the sensor’s range — that is the SHT31 component’s specification, not the finished device’s. Outside 0 to 80 °C the tolerance is larger; how much larger, Dragino does not say. For sub-zero temperatures one should therefore not count on two tenths of a degree, but hold the setup against a reference instrument once.

On the weight: the manufacturer states 370 g on the product page — the same figure as for the sibling device with three metres of probe cable, which is implausible for a device without one. The price list gives 230 g for the shipping unit. We therefore state no device weight and will add it after the first goods receipt.

+ Mostra altro

Dokumente

Recensioni

Ancora non ci sono recensioni.

Recensisci per primo “Dragino S31B-NS NB-IoT temperature and humidity sensor IP66 for outdoor use (868 MHz) — solar”

Details

Generale
Marca
Dragino
Codice produttore
S31B-NS-GE
Colore
nero
Connettività
Connettività
NB-IoT
NarrowBand Internet of Things, eine Low-Power-Wide-Area-Technologie, die speziell für das IoT entwickelt wurde, um eine größere Abdeckung mit geringerem Stromverbrauch zu ermöglichen.
Antenna esterna
sì
Alimentazione
Alimentazione
Batterie
,
Solarstrom
Pile incluse
Ja
Numero di pile
1
Tipo di pila
Li-Ion
Pila sostituibile
no
Meccanica/design
Larghezza (mm)
120
Lunghezza (mm)
200
Altezza (mm)
55
Codice IP / protezione
IP66
Staubdicht. Schutz gegen starkes Strahlwasser und bei Überflutung. Ein IoT-Sicherheitskamera im Freien könnte diesen Schutz haben.
Intervallo di temperatura
-40 °C bis 85 °C
Intervallo di umidità
0 bis 100% RH
Schede
Nano-SIM (4FF)
Informazioni commerciali
Paese d’origine
Cina
Altre caratteristiche
Sensori
umidità dell’aria
,
temperatura dell’aria
Luogo d’impiego
interno ed esterno