Dragino S31B-LS LoRaWAN temperature and humidity sensor IP66 for outdoor use (868 MHz) — solar

SKU:3JQT
Cod. produttore:S31B-LS
Marca:Dragino
Categorie:
Sensoren:
Sensoren Thumbnail Sensoren Thumbnail
Disponibilità CH:
non in magazzino0
Da magazzino esterno:
Tempo di consegnain ca. 20 giorni
Il termine vale a partire da 10 pezzi. Per quantità inferiori chiedeteci. (?)

CHF71.14 IVA escl.

più spese di spedizione

LoRaWAN temperature and humidity sensor in one piece: the Sensirion SHT31 sits in a condensation-proof sleeve directly on the IP66 enclosure, with no cable to route. ±0.2 °C and ±2 %RH, a stated long-term drift, and a solar panel with a rechargeable 3000 mAh Li-ion cell. For façades, halls and greenhouses, where the measuring point and the radio location are the same place.

! Per utilizzare questo dispositivo serve una rete LoRaWAN. Potete crearla voi stessi con un gateway LoRaWAN, usare la rete LORIOT o TTN, oppure la rete Swisscom LoRaWAN che copre tutta la Svizzera. Tutte queste reti sono acquistabili da noi.
 Aggiungi al confronto

The Dragino S31B-LS measures temperature and humidity where it hangs — sensor and radio are one piece. The Sensirion SHT31 sits in a condensation-proof sleeve directly on the enclosure: no cable to route, no second mounting point. The IP66 enclosure is built for outdoors, not merely tolerated there — which makes it the outdoor climate sensor you screw to a wall and forget for five years. This is the solar-powered version: a panel charges a rechargeable 3000 mAh Li-ion cell, and the battery change disappears as long as enough light arrives.

  • ±0.2 °Caccuracy, 0 … 90 °C
  • ±2 %RHhumidity, whole range
  • IP66enclosure
  • −40 … 85 °Coperating range
  • 3000 mAhLi-ion, solar charged

What defines the S31B-LS

  • One piece instead of two mounting points: the sensor sits in a sleeve attached directly to the enclosure. No cable to route, clamp or lead through a seal — mounting is one screwed fixing and done. Across a fleet of outdoor measuring points that is the difference between twenty minutes and five per device.
  • A Sensirion SHT31, not a house brand: the sensor fitted has a public datasheet and behaviour documented over years. ±0.2 °C and ±2 %RH are not marketing but the component’s specification — and they sit a class above what simple room sensors deliver.
  • The drift is stated, not glossed over: the manufacturer gives less than 0.03 °C and less than 0.25 %RH deviation per year. That is the figure which decides, over five years, whether a measurement series stays comparable — and the one that is simply missing from most cheap sensors.
  • Condensation-proof, not merely splash-proof: the sleeve lets humidity through but not water. That is exactly where open sensors fail outdoors: after the first condensation cycle they read permanently wrong.
  • The timestamp comes from the device: every message carries a Unix time from the sensor, not just the network server’s time of receipt. If delivery is delayed the series still stays chronologically correct — the precondition for it to serve as evidence.
  • An alarm flag in every message: a dedicated bit shows whether the value has left a set threshold. The evaluation therefore does not have to check thresholds itself, and an alarm is not lost if processing falls behind.
  • Recording when the network drops: if coverage fails, the device writes the readings to its own memory and sends them on once the network is back. For an evidential series that is the difference between a gap and continuity.
  • Device status on its own port: model, firmware version, frequency band and battery arrive on FPort 5, separate from the readings on FPort 2. For a fleet that means the inventory can be queried without searching the measurement database.
  • No battery change planned in: the solar panel charges a rechargeable 3000 mAh Li-ion cell. With sufficient light the replacement cycle disappears — at hard-to-reach measuring points the larger item over the service life. The cell is a buffer, not the main store: it carries the device overnight and through spells of bad weather.
  • Configuration over the air: reporting interval and thresholds are set by downlink. The device can also be configured on site over Bluetooth 5.1 and its firmware updated wirelessly — a device on a façade stays where it is.
  • Not tied to a platform: LoRaWAN 1.0.3, Class A, OTAA. Runs on TTN, ChirpStack and the Swisscom LPN with the same device profile and the same decoder.
  • Two forms of power, one article: where no battery change is wanted, the same device comes as the S31B-LS with a solar panel and a rechargeable cell. The measuring and radio sections are identical, the integration stays the same.

Where the S31B-LS is used

  • Outdoor climate on buildings: IP66 and a condensation-proof sleeve allow façade mounting; the operating range runs from −40 to 85 °C. This device’s classic application.
  • Unheated halls, barns, storage sheds: one device, one screw, no wiring — and reachable over radio even where no line runs.
  • Stores with humidity limits: paper, timber, electronics, animal feed. ±2 %RH is accurate enough to prove a limit and not merely assert it.
  • Greenhouse and polytunnel: the sensor hangs in the crop along with the device. Condensation-proof, so still able to measure after misting.
  • Building sites and temporary measuring points: mounted in minutes, removed just as fast, nothing to route.
  • Plant rooms and service risers: where the measuring point and the device location coincide, the compact form saves the second fixing.
  • Evidence towards third parties: thanks to the device’s own timestamp and the replay from memory the series stays continuous and chronological.
  • Large rollouts: one article, one decoder, one spare — and through the S31B-LS variant the solar-powered version as well, with no new integration.
No light, no solar operation. A LoRaWAN uplink costs little energy, so the balance is relaxed — but it stands or falls with where the panel sits. In the shade of a hedge, behind a roof edge or down a shaft it does not carry. Where the light is missing, the battery version S31B-LB is the right choice. Measurement happens where the device hangs. That is the whole difference from the sibling device: anyone who has to separate measuring point and radio location — cold store, shaft, hall ceiling — needs the S31 with three metres of probe cable. Both cost practically the same; the choice is one of mounting, not of budget. For plain indoor air measurement it is oversized. Where no outdoor climate and no ingress rating are needed, the Dragino LHT52 delivers the same for a fraction. IP66 is jets of water, not submersion. For a façade or a mast that is enough; in flood-prone locations the device belongs higher up. And the cell is not rechargeable. At the end of its life it is replaced, or the device is; anyone wanting to avoid that takes the solar version S31B-LS.

That covers the purchase decision. What follows is the depth needed for mounting, integration and operation.

Why the mounting location becomes a measured quantity here

On a device with a remote probe, the question “where do I measure” is separate from the question “where does the transmitter hang”. On the S31B the two coincide, and so the mounting location becomes part of the measurement. That is not a fault but a property to account for in planning — and one regularly overlooked in practice.

Consequence for planning: a black plastic enclosure in direct sun becomes warmer than the air it is meant to measure; depending on irradiation and wind that is several degrees. For outdoor air temperature the device therefore belongs on the north side, under a roof overhang or inside a radiation shield. The same applies in reverse to heat sources indoors: a device above a radiator or beside a switch cabinet measures the cabinet as well.

Assessment from field practice, not a manufacturer statement: the S31B shares this limitation with every compact sensor, and it is the real reason the cabled version exists at all. Anyone needing absolute outdoor air temperatures — for evidence, not for a trend — should plan for a radiation shield; anyone following trends and threshold breaches in a sheltered mounting position does not need one. Dragino makes no statement about sensitivity to radiation; on a device that hangs in arbitrary places that is hard to quantify anyway.

Payload and integration

The readings arrive on FPort 2 in a fixed order: two bytes of battery voltage in millivolts, four bytes of Unix timestamp, one byte with the alarm flag, the operating mode and the state of input PA8, then two bytes of temperature as a signed value with a factor of ten and two bytes of humidity with a factor of ten. Device status — model, firmware, frequency band, sub-band, battery — runs separately on FPort 5, and the replayed stored values on FPort 3.

For the integration that means two things. First: the decoder has to evaluate the port, otherwise status messages land in the time series as implausible readings — an error that only shows up when somebody analyses the data. Second: the supplied timestamp should be used as the measurement time, not the time of receipt. With LoRaWAN there may be minutes between measurement and delivery, and hours for replayed stored values; for an evidential series that is the difference between right and nearly right.

Solar operation — what carries the balance and what tips it

A LoRaWAN uplink costs little energy: the radio is awake for fractions of a second and then sleeps on at a few microamps. That makes the solar balance here considerably more relaxed than on a cellular device — the daily demand is low enough that even an overcast winter day usually still covers it. The rechargeable 3000 mAh Li-ion cell is not meant as the main store but as a buffer overnight and through spells of bad weather.

Consequence for planning: what decides is not the cell capacity but where the panel sits. Facing south and unshaded all day, the balance carries; in the shade of a hedge, behind a roof edge or down a shaft it does not — and that shows in December, not in June.

Assessment from field practice, not a manufacturer statement: for the solar version Dragino gives neither a battery life nor a minimum irradiation. With two independent variables — location and reporting interval — that is consistent, but it does not help with planning. What is usable is the cell voltage carried in every message: anyone recording it through the first winter knows afterwards whether the site carries, instead of guessing.

Data at a glance

SensorSensirion SHT31 in a watertight, condensation-proof sleeve, directly on the enclosure
Temperaturesensor −40 … +80 °C · ±0.2 °C in the range 0 … 90 °C · resolution 0.1 °C · long-term drift < 0.03 °C/yr
Humidity0 … 99.9 %RH · ±2 %RH across the whole range · resolution 0.01 %RH · long-term drift < 0.25 %RH/yr
Operating temperature−40 … 85 °C
RadioLoRaWAN 1.0.3, Class A, OTAA · EU868 · up to +22 dBm · sensitivity down to −139 dBm
PayloadFPort 2 readings · FPort 3 stored values · FPort 5 device status
ConfigurationLoRaWAN downlink · Bluetooth 5.1 on site · firmware update over the air
Powersolar panel with rechargeable 3000 mAh Li-ion cell · no battery-life figure from the manufacturer
EnclosureIP66 · 200 × 120 × 55 mm
VersionsS31B-LB LoRaWAN battery · S31B-LS LoRaWAN solar · S31B-NB NB-IoT · S31B-NS NB-IoT solar · S31B-CB LTE-M and NB-IoT · S31B-CS LTE-M and NB-IoT solar

On the measuring range: the manufacturer gives −40 to +80 °C for the sensor and an operating range of −40 to 85 °C for the device. The accuracy figure of ±0.2 °C refers to 0 to 90 °C and so reaches beyond the sensor’s range — that is the SHT31 component’s specification, not the finished device’s. Outside 0 to 80 °C the tolerance is larger; how much larger, Dragino does not say. For sub-zero temperatures one should therefore not count on two tenths of a degree, but hold the setup against a reference instrument once.

On the weight: the manufacturer states 370 g on the product page — the same figure as for the sibling device with three metres of probe cable, which is implausible for a device without one. The price list gives 230 g for the shipping unit. We therefore state no device weight and will add it after the first goods receipt.

+ Mostra altro

Dokumente

Recensioni

Ancora non ci sono recensioni.

Recensisci per primo “Dragino S31B-LS LoRaWAN temperature and humidity sensor IP66 for outdoor use (868 MHz) — solar”

Details

Generale
Marca
Dragino
Codice produttore
S31B-LS
Colore
nero
Interfaccia
LoRa 868MHz
Version des LoRa (Long Range) Low-Power-Wireless-Chipsatzes, der auf verschiedenen Frequenzen arbeitet. Typischerweise für IoT-Anwendungen mit geringem Stromverbrauch und großer Reichweite verwendet.
Connettività
Connettività
LoRaWAN
Long Range Wide Area Network, ein drahtloses Protokoll für Low-Power-Geräte in weiträumigen Netzwerken, ideal für das IoT.
Specifica LoRaWAN
1.0.3
Classe dispositivo
A
Klasse A-Geräte ermöglichen bidirektionale Kommunikation zwischen dem Gerät und dem Netzwerk. Nach jeder Uplink-Übertragung des Geräts sind zwei kurze Downlink-Empfangsfenster geöffnet. Diese Geräte haben die niedrigste Energieeffizienz und sind für Anwendungen geeignet, die keine festgelegten Empfangszeitpunkte erfordern. Beispielsweise könnte ein IoT-Sensor, der sporadisch Temperaturdaten an eine Cloud sendet, ein Klasse A-Gerät sein.
Antenna esterna
sì
Frequenze
EU868
LoRaWAN-Frequenzband für Europa (868 MHz). Verwendet in Ländern wie Deutschland, Frankreich, Großbritannien und den meisten anderen europäischen Ländern.
Alimentazione
Alimentazione
Batterie
,
Solarstrom
Pile incluse
Ja
Numero di pile
1
Tipo di pila
Li-Ion
Pila sostituibile
no
Meccanica/design
Larghezza (mm)
120
Lunghezza (mm)
200
Altezza (mm)
55
Codice IP / protezione
IP66
Staubdicht. Schutz gegen starkes Strahlwasser und bei Überflutung. Ein IoT-Sicherheitskamera im Freien könnte diesen Schutz haben.
Intervallo di temperatura
-40 °C bis 85 °C
Intervallo di umidità
0 bis 100% RH
Informazioni commerciali
Paese d’origine
Cina
Altre caratteristiche
Sensori
umidità dell’aria
,
temperatura dell’aria
Luogo d’impiego
interno ed esterno
Server di rete
ChirpStack
,
Swisscom LPN
,
TTN