The Adeunis Fieldtester answers the question that precedes every rollout: will my device work at this spot at all? It measures the coverage and quality of NB-IoT and LTE-M networks where the sensors are to hang later — in the basement, in the hall, on the mast. Every measuring point is located automatically and can be shown on a map or a building plan. The device replaces the approach of mounting a hundred sensors and discovering afterwards that thirty of them get no connection.
- 3 modesscan, test, radio mapping
- 15 daysat 12 hours of use per day
- 101 g107 × 76 × 23 mm
- NB-IoT · LTE-Mboth technologies, worldwide bands
What the Fieldtester does
- It measures where the device will stand: an operator’s coverage map applies to the street, not to the boiler room two floors below. The difference between the two is exactly why rollouts fail — and the reason this device exists.
- Three modes for three questions: the network scan searches for everything in range and rates it. The network test checks the quality of one particular operator. The radio mapping project gathers many measuring points into a report — that is the mode for a whole building or site.
- Every measuring point knows where it was: location is handled automatically by GNSS. A series of measurements thus becomes a map instead of a list of figures nobody can place afterwards.
- On the building plan too: indoors, where GNSS does not reach, the points can be shown on a floor plan. That is precisely where the critical spots are.
- Both technologies in one device: NB-IoT and LTE-M behave considerably differently — NB-IoT penetrates deeper, LTE-M behaves better on the move. Which of the two carries at a specific place can only be measured, not deduced.
- Operator independent: with a single- or multi-operator SIM, networks can be compared directly against one another. That is the solid basis for choosing a provider.
- Two weeks in the field: at twelve hours of use a day the built-in battery lasts around fifteen days. A measuring campaign across a site can therefore be run without a charging break.
- Made in France: developed and built by Adeunis — for tenders in which origin has to be proven.
Where it is needed
- Before the rollout: the main case. Check that the planned mounting points carry, before devices are ordered and fitters sent out.
- In fault finding: a sensor does not report — is it the device, the SIM or the network? The Fieldtester settles the question in ten minutes.
- When comparing providers: measure two operators at the same place instead of holding coverage maps against each other.
- At handover: a documented measurement report proves to the client that coverage was present on the day of handover.
- In buildings and underground car parks: anywhere several concrete floors lie between the street and the measuring point.
- For planning offices and integrators: one device used across many projects, paying for itself after a few avoided planning errors.
That settles the selection. What follows is the depth for use.
Why NB-IoT and LTE-M belong measured separately
The two technologies share the bands but behave differently. NB-IoT is designed for penetration: narrowband, with many repetitions, but sluggish to establish a connection and poorly suited to devices that change location. LTE-M has more bandwidth, changes cell in service and suits mobile applications, but penetrates less deeply. A basement in which NB-IoT still carries can already be too deep for LTE-M — and conversely NB-IoT fails with a device that moves.
From this follows, for measuring: check both technologies at the same point, not one and assume the rest. The Fieldtester does that in a single pass, and only this comparison makes the decision solid. This assessment comes from practical application and is to be understood as a selection aid.
How a measuring campaign is built
A single reading at one point says little — radio fluctuates over time. For a solid statement you measure several times at each planned mounting point and at different times of day, because network load affects throughput. What matters is finding the least favourable point, not the average one: a rollout does not fail on the mean but on the worst ten per cent of locations.
Practical advice: measure where the device will actually hang — in the recess behind the pipe, not a metre away in open space. In plant rooms the difference regularly exceeds anything antenna optimisation can deliver.
Technical data
The general product data — dimensions, weight, housing, battery, supported bands, manufacturer part number and origin — is in the detail table further down this page.
| Modes | network scan, network test, radio mapping project with report |
| Technologies | NB-IoT (Cat-NB1/NB2) and LTE-M (Cat-M1) |
| Location | GNSS, automatic per measuring point; indoors shown on a building plan |
| SIM | nano SIM (4FF), single- or multi-operator card, not included |
| Battery life | around 15 days at 12 hours of use per day |
| Battery | lithium-ion, built in, not replaceable |
| Charging and connection | USB Type-C, 900 mA |
| Further interface | Bluetooth Low Energy |
| Operating conditions | 0 … 45 °C, 0 … 85 % relative humidity |
| Memory | internal |
Scope of delivery
- 1 × Adeunis Fieldtester NB-IoT / LTE-M with built-in battery, part number ARF8393AAA
- No SIM card — that is ordered separately, preferably as a multi-operator card
The matching counterpart
- For LoRaWAN: the Adeunis Field Test Device LoRaWAN 868 MHz is the corresponding tool for LoRaWAN networks. Anyone using both technologies needs both devices.
Help with use
Unsure whether NB-IoT or LTE-M is the right technology for your plans, or how a measuring campaign across a site is built? Tell us what you want to equip — this question is gladly settled in conversation, because it decides the success of the whole rollout. And if it turns into a project — measuring campaign, analysis or handover report — we will gladly put together a quote.

Reviews
There are no reviews yet.